The VD-420 Wireless Manual Flash from Bolt can be used as both a wireless slave and manual on-camera flash, providing plenty of creative options for flash placement. The included transmitter can be used to fire the flash from up to 50 away. The flash s output level can be manually adjusted from 1/128 to full power in eight full-stop increments. An LED provides a visual reference to the output level in bright or low-light environments. Optical wireless slave modes allow additional off-camera triggering for greater control over the light in your setup.
Features At a Glance
- Built-in 433 MHz wireless receiver
- Wireless hot shoe transmitter included
- Eight manual flash levels: 1/1 to 1/128 power
- 16 wireless channels
- Optical slave with S1 and S2 modes
- Tilting angle: 90° up, -7° down
- Rotational angle: -180° left, 90° right
- 3.5mm sync connectivity
- High-voltage battery pack connectivity
- Built-in reflector and diffuser panels
- Automatic power-saving function
- Automatic overheating protection
Wireless Operation
The VD-420 offers wireless operation via radio frequency or optical sensor. Using the included transmitter, it can be triggered from up to 50 away. 16-wireless channels allow the flash to be triggered with no interference from other radio triggers. There are two optical modes, S1 and S2. In S1 mode the flash triggers when it sees any burst of light from the master flash. In S2 mode, the flash will ignore 1 pre-flash and fire on the second burst of light.
Eight Manual Flash Levels
Adjust the output power level from 1/128 to full power in eight full-stop increments. Intuitive analog controls and LED indicators display power settings, flash mode, and status.
Adjustable Light Direction
The VD-420 is equipped to laterally rotate the flash head up to 270° and tilt a total of 97° . This is perfect for bouncing the light off a surface for softer, more pleasing illumination on the subject.
433 MHz Wireless Transmitter
The included 433 MHz wireless transmitter is a compact 2.4 x 1.6 x 1.1" , and slides onto any camera s hot shoe for easy triggering. It also has a 2.5mm synch input cable for additional triggering options. It has a manual triggering button and LED indicator and operates on a long-life 12V battery.
Batteries and External Power
The VD-420 operates on four AA alkaline, NiMH, or lithium batteries, available separately. In addition, it can be connected to an external power source via the extended interface on the side of the flash. This can greatly increase the battery and reduce the recycle time in between flashes.
NOTE: When using an external power supply, it is still necessary for there to be four AA batteries in the flash unit for operational purposes.
3.5mm Sync Terminal
An integrated 3.5mm sync cable receiver socket allows the VD-420 to be triggered while connected to radio remotes or the camera.
EAN: 847628054899
Bolt VD-420 Specs
Flash Head
| Guide Number | 108.3` / 33 m at ISO 100 |
| Bounce Head | -7 to +90° |
| Swivel Head | 270° |
| Flash Duration | 1/300 to 1/20,000 Second |
| Recycle Time | Approx. 0.1 to 5 Seconds |
| Secondary Illumination | None |
Exposure Control
| Exposure Control | Manual |
| Flash Modes | None |
| Power Range | 1/1 to 1/128 (Manual) |
| Flash Compensation | None |
Wireless
| Wireless Operation | Radio (Manual) Up to 49.2` / 15 m |
| Wireless Channels | 16 |
| Wireless Groups | None |
| Remote Timing Modes | Instant Sync Skip Preflash |
Power
| Internal Power | 4 x AA (Alkaline, Lithium-Ion, NiMH) |
| External Power Pack Compatible | Yes |
General
| Mount | Shoe |
| Off-Camera Terminal | 1/8" / 3.5 mm |
| Dimensions (W x H x D) | 7.3 x 2.8 x 2.1" / 18.5 x 7.1 x 5.3 cm |
| Weight | 10.9 oz / 310 g (without Battery) |
Packaging Info
| Package Weight | 0.985 lb |
| Box Dimensions (LxWxH) | 8.95 x 3.4 x 2.85" |
In the Box
- Bolt VD-420 Wireless Manual Flash
- Transmitter
- Stand / Tripod Mount
- Drawstring Pouch
- 2-Year Manufacturer Warranty
Not in the Box
- Essential Batteries & Power (Not Included)
Customer reviews
Recommendation for purchase
