The 4-Channel 1000W Network-Enabled Power Amplifier from Ashly delivers a minimum power of 250W RMS power per channel into 70V loads with all channels operating. The amplifier features pre-installed AES3 input card with pass-thru and the Protea DSP Software Suite and is designed around an energy efficient Class-D platform with a switching power supply. When switched into bridged-mono mode, channels 1+2 or 3+4 of the amplifier delivers over 500W RMS into an 140V load.
The power amplifier includes Euroblock input connectors, Euroblock output connectors, and balanced analog inputs. Besides remote standby for power up, DC remote level control, and contact closure preset recall, the amplifier also features Ethernet control & monitoring of power functions, level, mute, polarity, temperature, current, and amplifier fault conditions. The front panel indicates power status, standby, protect, power switch On/Off, signal level, bridge, temperature & current levels, and Ethernet communication. The amplifier mounts in a standard 19 ? rack using two spaces (3.5 ? high).
The power amplifier has an internal factory-installed Digital Signal Processing (DSP) controlled using the Protea Software Suite (network-enabled). Each amplifier input channel can be configured with pluggable DSP blocks to have its own dynamics control, gain functions, graphic and/or parametric EQ, Hi-pass/Lo-pass filters, time delay, metering, and test signal generator. A mixer section with assignable routing allows any input to drive any or all amplifier outputs.
Outputs have the same DSP functions as inputs, with the addition of a quick and automated crossover setup. Both inputs and outputs duplicate their settings to other channels, or link with one or more other channels to track their settings. Presets can be used to store and retrieve global parameters of an amplifier s control surface and DSP section from a file. Sub-presets allows for a collection of individual DSP function parameters within and across both channels of an amplifier to be stored and recalled as a set, affecting only those parameters which have been tagged. Up to 35 presets/sub-presets can be stored within the amplifier and recalled in real time via Ethernet from a computer using the Protea Software Suite.
- 10/100 Ethernet for remote control and monitoring
- 70V constant voltage
- Pre-installed AES3 input card with pass-thru and Protea DSP Software Suite
- DC voltage remote gain control
- Switched-mode power supply, Class-D output
- Stepped & calibrated input attenuators
- Remote power standby
- All front panel controls can be disabled via software
- Temperature-sensitive variable speed fan with front-to-back airflow
- Selectable HPF frequencies (80 Hz, 400 Hz, off)
- 4-stage level meters
- Output current and temperature indicators
- cTUVus, CE, FCC, and RoHS safety/compliance
Ashly NE4250.70PEA Specs
Amplifier
| Frequency Response | 20 Hz to 20 kHz, (unweighted) ± 1 dB |
| Input Impedance | 20 kOhms, balanced |
| Voltage Gain | 32 dB |
| Input Sensitivity | 7.2 dBu |
| Maximum Input Level | +21 dBu |
| Software Control | 80 Hz (12 dB/oct), 400 Hz (6 dB/oct), Off |
| Distortion | 8 Ohms load: < 0.5 % typical (SMPTE) < 0.5 % typical (20 Hz to 20 kHz) (THD-N) |
| Damping Factor | > 250 (8 Ohms, 1 kHz) |
| Circuitry | Class D |
| Maximum load protection | Output Overcurrent, Main Supply Rail Overvoltage, Chassis Temperature, Inrush Limiting, Mains Fuse |
| Controls | Remote standby, Preset recall (4), Remote Level (8), Remote Data |
| Connectors | Input/Output: Euroblock (each channel) |
| Required AC Mains | 120 VAC or 240 VAC, ±10% 50 to 60 Hz |
| Cable Connectors | 15 A Edison, 3-Prong IEC |
| Signal to Noise Ratio | > 107 dB (20 Hz to 20 kHz, unweighted) |
| LED Indicators | Signal Level Red: Clip Yellow: -6 dB Green: -18 dB, -12 dB Bridge: Green per channel pair Temperature: Yellow per channel Current: Green per channel (proportional to output) |
| Output | 250 W per channel |
| Current Draw | Standby Mode: 290 mA Idle (No Signal): 565 mA Typical (1/8 Power Pink Noise): 5.00 A Maximum (1/3 Power Pink Noise): 11.0 A |
| Thermal Dissipation | Standby Mode: 63.8 BTU/hr Idle (No Signal): 187 BTU/hr Typical (1/8 Power Pink Noise): 700 BTU/hr Maximum (1/3 Power Pink Noise): 775 BTU/hr |
| Dimensions | 19 x 3.5 x 16" (48 x 8.9 x 41 cm) |
| Weight | 18 lb (8.2 kg) |
In the Box
- Ashly 4-Channel 1000W Network-Enabled Power Amplifier with AES3 & Protea DSP Software Suite (70V)
- 5-Year Manufacturer Warranty
No posts found
