Shipping time and rates:
Shipping time and rates:
Sorry, we couldn't find any shipping options for your location. Please contact us, and we'll see what we can do about it.
Yes, we can ship to
United States
Ashly 8-Channel 2000W Network-Enabled Power Amplifier with OPDAC8 and OPDante Cards (Low-Z)
The 8-Channel 2000W Network-Enabled Power Amplifier from Ashly delivers a minimum power of 150W RMS per channel into 8 ohm loads and 250W RMS per channel into 4 ohm loads with all channels operating. The amplifier features OPDAC8 digital to analog converter with selectable high-pass filter and OPDante network audio interface cards; and is designed around an energy efficient Class-D platform with a switching power supply. When switched into bridged-mono mode, channels 1+2, 3+4, 5+6, or 7+8 of the amplifier delivers over 500W RMS into an 8 ohm load.
The power amplifier includes Euroblock input connectors, Euroblock output connectors, and balanced analog inputs. Besides remote standby for power up, DC remote level control, and contact closure preset recall, the amplifier also features Ethernet control & monitoring of power functions, level, mute, polarity, temperature, current, and amplifier fault conditions. The front panel indicates power status, standby, protect, power switch On/Off, signal level, bridge, temperature & current levels, and Ethernet communication. The amplifier mounts in a standard 19`? rack using two spaces (3.5`? high).
10/100 Ethernet comes standard for remote control and monitoring
Low-Z (4 Ohms)
OPDAC8 and OPDante input options
DC voltage remote gain control
Switched-mode power supply, Class-D output
Stepped, calibrated input attenuators
Remote power standby
Disable all front panel controls via software
Temperature sensitive variable speed fan with front-to-back airflow
Four stage level meters
Output current and temp indicators
Safety/Compliance: cTUVus, CE, FCC, RoHS
The 8-Channel 2000W Network-Enabled Power Amplifier from Ashly delivers a minimum power of 150W RMS per channel into 8 ohm loads and 250W RMS per channel into 4 ohm loads with all channels operating. The amplifier features OPDAC8 digital to analog converter with selectable high-pass filter and OPDante network audio interface cards; and is designed around an energy efficient Class-D platform with a switching power supply. When switched into bridged-mono mode, channels 1+2, 3+4, 5+6, or 7+8 of the amplifier delivers over 500W RMS into an 8 ohm load.
The power amplifier includes Euroblock input connectors, Euroblock output connectors, and balanced analog inputs. Besides remote standby for power up, DC remote level control, and contact closure preset recall, the amplifier also features Ethernet control & monitoring of power functions, level, mute, polarity, temperature, current, and amplifier fault conditions. The front panel indicates power status, standby, protect, power switch On/Off, signal level, bridge, temperature & current levels, and Ethernet communication. The amplifier mounts in a standard 19`? rack using two spaces (3.5`? high).
10/100 Ethernet comes standard for remote control and monitoring
Low-Z (4 Ohms)
OPDAC8 and OPDante input options
DC voltage remote gain control
Switched-mode power supply, Class-D output
Stepped, calibrated input attenuators
Remote power standby
Disable all front panel controls via software
Temperature sensitive variable speed fan with front-to-back airflow
Four stage level meters
Output current and temp indicators
Safety/Compliance: cTUVus, CE, FCC, RoHS
Ashly NE8250BD Specs
| Frequency Response | 20 Hz to 20 kHz, (unweighted) ±1dB |
| Input Impedance | 20 kOhms, balanced |
| Voltage Gain | 26 dB |
| Input Sensitivity | 6.2 dBu |
| Maximum Input Level | +21 dBu |
| Distortion | 8 Ohms load < 0.5 % typical (SMPTE) < 0.5 % typical (20 Hz to 20 kHz) (THD-N) |
| Damping Factor | > 250 (8 Ohms, 1 kHz) |
| Circuitry | Output: Class D |
| Amplifier Protection | Output overcurrent, main supply rail overvoltage, chassis temperature, inrush limiting, and main fuse |
| Controls | Ethernet 10/100, Channel bridge switch (Low-Z only), Remote standby, Preset recall (4), Remote Level (8), Remote Data |
| Connectors | Input/Output: Euroblock (each channel) |
| Required AC Mains | 120 VAC or 240 VAC, ±10% 50 to 60Hz |
| Cable Connectors | 15 A Edison, 3-Prong IEC |
| Signal to Noise Ratio | > 107 dB (20 Hz to 20 kHz, unweighted) |
| LED Indicators | Signal Level Red: Clip Yellow: -6 dB Green: -18 dB, -12 dB Bridge: Green per channel pair Temperature: Yellow per channel Current: Green per channel (proportional to output) |
| Output | Average Power: 8 Ohms (150 W), 4 ohms (250 W) Bridge Mode: 8 Ohms (500 W) |
| Current Draw | Standby Mode: 290 mA Idle (no signal): 565 mA Typical (1/8 power pink noise): 5.00 A Maximum (1/3 power pink noise): 11.0 A |
| Thermal Dissipation | Standby Mode: 63.8 BTU/hr Idle (no signal): 187 BTU/hr Typical (1/8 power pink noise): 700 BTU/hr Maximum (1/3 power pink noise): 775 BTU/hr |
| Dimensions | 19 x 3.5 x 15.5" (2.5 x 8.9 x 39.3 cm) |
| Weight | 19.7 lb (8.9 kg) |
In the Box
- Ashly 8-Channel 2000W Network-Enabled Power Amplifier with OPDAC8 and OPDante Cards (Low-Z)
- 5-Year Manufacturer Warranty
No posts found
