Shipping time and rates:
Shipping time and rates:
Sorry, we couldn't find any shipping options for your location. Please contact us, and we'll see what we can do about it.
Yes, we can ship to
United States
Ashly nXe3.04 Network Power Amplifier
The nXe3.04 Network Power Amplifier from Ashly Audio is the networkable version of the nX amplifier. It comes with Ethernet control, serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability. All these are controlled using Ashly Audio`s Protea software suite. This amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.
2-channel high-output, lightweight amplifier with programmable output on each channel
Power saving, Energy Management System (Ashly EMS) automatic <1W sleep mode is defeatable
Front panel power switch and level controls can be disabled for security
Neutrik Combo XLR: 1/4` TRS jack plus Euroblock input connectors
Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability
Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration
Ethernet port for use with control and monitoring of amplifier functions, with front panel COM activity LED
Serial data port for use with Ashly remote control devices, or RS-232 converter (sold separately) for third party controllers (INA-1)
Uses Protea software to remotely disable all front panel controls, including the on/off switch, for a tamper-proof installation
Real-time clock with event scheduler
Instant standby mode, 30% reduction in power consumption with on/off triggered by contact closure, software control, or event scheduler
Programmable power-on delay
Preset recall via contact closure, software control, remote control, or event scheduler
Auxiliary preamplifier outputs and fault condition logic outputs
Cobranet or Dante network audio (sold separately) and AES3 digital audio input with pass-through
Ducking at mixer, peak hold indicator, in/out per filter, key engage, lock per filter, and global lock
The nXe3.04 Network Power Amplifier from Ashly Audio is the networkable version of the nX amplifier. It comes with Ethernet control, serial data control, aux preamp outputs, instant standby mode, preset recall, fault condition logic outputs, and optional network audio and digital audio capability. All these are controlled using Ashly Audio`s Protea software suite. This amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces, and convention centers.
2-channel high-output, lightweight amplifier with programmable output on each channel
Power saving, Energy Management System (Ashly EMS) automatic <1W sleep mode is defeatable
Front panel power switch and level controls can be disabled for security
Neutrik Combo XLR: 1/4` TRS jack plus Euroblock input connectors
Neutrik speakON twist locking loudspeaker connectors for security, safety, and reliability
Rear panel DIP switches per channel for selection of high pass filter, limiter, input gain, and High-Z or Low-Z speaker output configuration
Ethernet port for use with control and monitoring of amplifier functions, with front panel COM activity LED
Serial data port for use with Ashly remote control devices, or RS-232 converter (sold separately) for third party controllers (INA-1)
Uses Protea software to remotely disable all front panel controls, including the on/off switch, for a tamper-proof installation
Real-time clock with event scheduler
Instant standby mode, 30% reduction in power consumption with on/off triggered by contact closure, software control, or event scheduler
Programmable power-on delay
Preset recall via contact closure, software control, remote control, or event scheduler
Auxiliary preamplifier outputs and fault condition logic outputs
Cobranet or Dante network audio (sold separately) and AES3 digital audio input with pass-through
Ducking at mixer, peak hold indicator, in/out per filter, key engage, lock per filter, and global lock
Ashly nXE3.04 Specs
General
| Voltage Gain | Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V |
| Damping Factor | >250 (8 © load <1 kHz) |
| Filter | Input High Pass Filter: 80 Hz 2nd order |
| Distortion | <0.5% SMPTE, typical <0.5% THD-N, typical (8 ©, 10 dB below rated power, 20 Hz to 20 kHz) |
| Channel Separation | -75 dB (dB from full output, 1 kHz) |
| Signal / Noise | 20 Hz to 20 kHz, un-weighted >114 dB (all 3.0x models) |
| Frequency Response | 20 Hz to 20 kHz, ±0.05 dB |
| Connector | Balanced Input Connector: Euroblock 3.5 mm, 1/4" TRS and XLR combo jack |
| Input Impedance | 10 k© |
| Maximum Input Level | +21 dBu |
| Speaker Output | Connector: Neutrik & speakON |
| Network | Control Network: Compatible with standard 100 MB Ethernet |
| AUX Outputs | Connector: Balanced Euroblock 3.5 mm Maximum Output: 21 dBu |
| Contact Closure | Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall |
| Data | Data Connection: Euroblock 3.5 mm - Gnd, +18 V, In, Out |
| Level Control | Remote DC: Euroblock 3.5 mm - Gnd, CV, V+ per input |
| Attenuation | Front panel, software, offset link group, and remote per channel fully off = mute |
| Amplifier | Amplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses |
| Cooling | Continuously variable temperature controlled axial fan(s) |
| Environmental | Non-condensing 32 to 113ºF (0 to 45ºC) |
Power Requirements
| Power | At 50 Hz Nominal (Automatic Sensing SMPS): 240 VAC Operating Range: 70 to 135 VAC Minimum Power-Up: 85 VAC At 60 Hz Nominal (Automatic Sensing SMPS): 240 VAC Operating Range: 140 to 270 VAC Minimum Power-Up: 170 VAC |
| Connector | Power Cable Connector: 32 A powerCON |
| Output | For Max Output Power Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1% THD & Low Z Output: 2 ©: 3,000 W 4 ©: 2,000 W 8 ©: 1,250 W For Low Z output, Bridge Mode, 20 Hz to 20 kHz & 1% THD: 4 ©: 6,000 W For Output Per Channel: 70 V: 2,450 W 100 V: 1,250 W Note: All Channels Driven |
| Power Draw | Sleep Mode: < 1 W Standby Mode: 70 W Idle (No Signal): 100 W Note: All Channels Driven |
| Current Draw | For 240 VAC Sleep Mode: 0.1 A Standby Mode: 1.30 A Idle (No Signal): 1.85 A For 240 VAC Sleep Mode: 0.2 A Standby Mode: 0.65 A Idle (No Signal): 0.92 A Maximum for all Channels Driven: For 240 VAC Typical: 29.5 A For 240 VAC Typical: 14.7 A |
| Dissipation | Thermal Dissipation: Sleep Mode: <3.4 BTU/hr Standby Mode: 238 BTU/hr Idle (no signal): 340 BTU/hr Typical (1 / 8 Max Power): 2,720 BTU/hr Note: All Channels Driven |
| LED Indicators | Front Panel LED Indicators: White LED: Power Switch: On, off, standby (flashing) Red LED: Clip / Mute Per Channel: Clip @ 1 dB below full output / mute Protect: On, Off Green LED: Signal Per Channel: -18 dBu Bridge Per Channel Pair: On, off Com: On, for Ethernet data or device ID Current Per Channel: Proportional to output Yellow LED: Temperature Per Channel: On dim at 90% max operating temperature, full bright + protect at 100% Sleep: On, amplifier is asleep from audio inactivity Disable: On, power switch & front panel attenuators are disabled |
Processor
| Input Source | Protēa DSP Options: Analog, auto (net, AES3, analog) Note: All DSP functions can be linked to 1 of 16 link groups |
| Limiter | Brick Wall Limiter: Threshold: -20 to 20 dBu Ratio: Infinite Attack: 0.2 to 50 ms/dB Release: 5 to 1000 ms/dB |
| Control | Advanced Gate Controls: Key Engage Enable: Yes Key Frequency: 20 Hz to 20 kHz Key Bandwidth: 0.016 to 3.995 octave |
| Gain | Gain (with / without VCA): -50 to 12 dB, off, polarity invert Digital VCA Groups: 4 available Remote RD8C Gain: Enable per channel, 0 dB to -₧ WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute |
| EQ Type | For 31-Band Filter Type: Constant Q or proportional Bandwidth: 0.499 octave to 0.25 octave For Parametric 2,4,6, or 10 Band Frequency: 20 to 20 kHz Level: -30 to 15 dB Q Value: 0.016 to 3.995 octave For Hi / Low Shelf 6 / 12 dB/octave Frequency: 20 Hz to 20 kHz Level: -15 to 15 dB For All Pass Frequency: 20 Hz to 20 kHz For Variable Q HP / LP Frequency: 20 Hz to 20 kHz Q Value: 3.047 to 0.267 For Notch / Bandpass Frequency: 20 Hz to 20 kHz Q Value: 92.436 to 0.267 |
| Crossover | 2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave Frequency: Off, 20 Hz to 20 kHz |
| Delay | Sampling Rate: At 48kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 21 ms Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature) Speaker Delay: 0 to 10.6 ms Delay: 0 to 341 ms |
| Audio Metering | Range: -60 to 20 dBu Increments: 1 dB Peak Hold Indicator: Yes |
| Signal Generator | Pink Noise, White Noise, Sine Wave Signal Level: Off, -50 to 20 dBu Sine Wave Frequency: 20 Hz to12 kHz |
| Processor | Input A/D, Output D/A: 24 bit DSP Processors: 32-bit floating point Sample Rates: 48 kHz, 96 kHz Propagation Delay @ 48 kHz: 1.42 ms Propagation Delay @ 96 kHz: 0.71 ms |
| Mixer | Gain (0.5 dB Increments): Off, -50 to 12dB Mute: Per channel Auto-mixer Enabled: Per channel Global Auto-mixer Response: 0.01 to 2 sec Enable Ducking at Mixer: Yes Ducking LED: Per channel if enabled Metering: Level, auto-mixer level |
| Filters | Number: 12 In/Out per filter: Yes Lock per filter and global lock: Yes Filter Modes: Float, Restricted, Manual Filter Type: Notch, Parametric Filter Frequency Range: 20 Hz to 20 kHz Notch Filter: -₧ Parametric Filter: 15 dB to -30 dB Filter Bandwidth: 0.016 to 3.995 octave Detector Sensitivity: 5 levels Float Time: 5 minutes to 24 hours |
Compressor
| Threshold | -20 to 20 dBu |
| Ratio | 1.2:1 to infinite |
| Attack | 0.2 to 50 ms |
| Release | 5 to 1000 ms/dB |
| Detectors | Peak / average |
| Attenuation | 2 available |
| Metering | In, out, attenuation, graphical |
Controls
| Level | Target Level: -40 to 20 dBu |
| Action Type | Gentle, normal, aggressive, user defined |
| Maximum Gain | 0 to 22 dB |
| Metering | Input, gain, attenuation |
| Ratio | 1.2:1 to 10:1 |
| Threshold | -30 to 0 dB |
| Gain | 5 to 1000 ms/dB |
| Hold | 0 to 6 seconds |
Noise Characteristics
| Gain | Maximum: -20 to 20 dB Minimum Base: In the Box
No posts found Similar productsAt the same price!
|
