Lectrosonics DNT16i - 16 Analog Input Dante Network Processor
The DNT16i from Lectrosonics is a processor that provides inputs into a Dante network from analog and digital signals. Each input provides extensive signal processing and routing to any one or all of forty-eight automatic mixers operating at the cross points of an internal digital matrix in the processor.
The outputs of the matrix can be assigned to a Dante transmit channel and/or routed back to an input to be further mixed with another input or matrix mix.
Sixteen microphone/line analog inputs with 48V phantom power and wide range gain control
Sixteen Dante digital inputs
Thirty-two Dante digital outputs
Supports both switched and redundant modes in Dante operation
Pre-mixing signal processing on all thirty-two inputs (analog and digital)
Forty-eight independent automatic mixers with thirty-six inputs per mixer and channel activity detectors
Support for multi-level mixing - mixes can be looped back and used as mixer inputs
Extensive signal processing including filters, delay and channel linking for dynamic processing (compressors, limiters)
Gain smoothing to prevent transient noise during instantaneous level changes
Four test signal generators available for system setup and testing
Extensive macro command language
Control interfaces via USB, RS-232, Ethernet and programmable logic I/O
Rack mount or under table mount
The DNT16i from Lectrosonics is a processor that provides inputs into a Dante network from analog and digital signals. Each input provides extensive signal processing and routing to any one or all of forty-eight automatic mixers operating at the cross points of an internal digital matrix in the processor.
The outputs of the matrix can be assigned to a Dante transmit channel and/or routed back to an input to be further mixed with another input or matrix mix.
Sixteen microphone/line analog inputs with 48V phantom power and wide range gain control
Sixteen Dante digital inputs
Thirty-two Dante digital outputs
Supports both switched and redundant modes in Dante operation
Pre-mixing signal processing on all thirty-two inputs (analog and digital)
Forty-eight independent automatic mixers with thirty-six inputs per mixer and channel activity detectors
Support for multi-level mixing - mixes can be looped back and used as mixer inputs
Extensive signal processing including filters, delay and channel linking for dynamic processing (compressors, limiters)
Gain smoothing to prevent transient noise during instantaneous level changes
Four test signal generators available for system setup and testing
Extensive macro command language
Control interfaces via USB, RS-232, Ethernet and programmable logic I/O
Rack mount or under table mount
Lectrosonics DNT16I Specs
| Audio Inputs | (Balanced microphone/line level inputs with digitally programmable gain may be configured as unbalanced inputs) Audio Input Channels Analog: 16 mic/line level Digital: 16 Dante channels Gain Analog: 0 dB to 56 dB, programmable in 8 dB steps (the analog gain is automatically set by selecting the input gain) Digital (Dante): -70 dB to +20 dB Performance Impedance: 8k© differential mode, 2k© common mode Maximum Analog Input Level: 20 dBu Dynamic Range: 102 dB EIN: -127 dBu (20 Hz to 20 kHz, unweighted) THD + Noise: 0.01% A-D Sampling Rate: 48 kHz, fixed |
| Audio Outputs | Digital: 32 outputs delivered to the Dante network |
| Dante Interface | Provides dual RJ-45 connectors on the rear panel and an Ethernet switch built into the processor Supported Sampling Rate: 48 kHz Data Rate LED: 100 Mbps/1 Gbps Activity LED: Blinks when active Modes of Operation Switched mode using either connector Redundant mode with primary and secondary networks using both connectors |
| Network Connectivity | Dante interface and Ethernet control can be connected to the same network |
| Filters | All filters have zero processing delay Tone Control Stages: 4 per input channel ADFE: 8 per input channel, configurable as static or dynamic |
| Internal Signal Generator | Swept Sine Modes: Single sweep, continuous sweep Waveforms: Sawtooth (up or down), triangle Sweep Rate: Linear, logarithmic Parameters: Start freq, stop freq, level (dBu), sweep time (sec) White Noise Parameter: Level (dBu) Pink Noise Parameter: Level (dBu) Tone (Sine Wave) Parameters: Level (dBu), frequency |
| Filter Type | Low Pass Butterworth 6, 12, 18, 24 dB/octave Bessel 6, 12, 18, 24 dB/octave Linkwitz-Riley 12, 24 dB/octave Additional Parameters: Frequency (Hz) High Pass Butterworth 6, 12, 18, 24 dB/octave Bessel 6, 12, 18, 24 dB/octave Linkwitz-Riley 12, 24 dB/octave Additional Parameters: Frequency (Hz) Low Shelving Butterworth 6, 12, 18, 24 dB/octave Bessel 6, 12, 18, 24 dB/octave Additional Parameters: Frequency (Hz), boost/cut (dB) High Shelving Butterworth 6, 12, 18, 24 dB/octave Bessel 6, 12, 18, 24 dB/octave Additional Parameters: Frequency (Hz), boost/cut (dB) Peaking EQ Parametric Parameters: Frequency (Hz), bandwidth (octave), boost/cut (dB) |
| Compressor | Soft knee with RMS level detector eliminates need for separate attack and delay settings 0.1 ms increments 1 second maximum Continuously adjustable ratio |
| Power Requirements | 100~240 VAC, 50/60 Hz 20 W maximum consumption |
| Dimensions | 19 x 7.7 x 1.75" (483 x 196 x 44 mm) |
| Weight | 5.3 lb (1.7 kg) |
Packaging Info
| Package Weight | 2 lb |
| Box Dimensions (LxWxH) | 25 x 15 x 7" |
In the Box
- Lectrosonics DNT16i - 16 Analog Input Dante Network Processor
- AC Power Cable
- 3-Year Manufacturer Warranty
No posts found
