Designed to provide the basic accessories for shock-mounting a shotgun microphone atop a camera for indoor or outdoor environments, this features the Sanken CS-M1 moisture-resistant ultracompact shotgun microphone, a Rycote shoe/boompole shockmount, and a Rycote Classic-Softie windshield.
The kit addresses the needs of videographers who prefer a high-quality shotgun microphone setup that stays out of the frame while delivering professional mix-ready tone, low handling noise, and minimal wind noise. With its XLR output, phantom powering, low self-noise, and ultrahigh sensitivity, the CS-M1 mic is well suited for use with professional camcorders, multitrack field recorders, and portable audio recorders.
Sanken CS-M1 Moisture-Resistant Ultracompact Shotgun Microphone
Little more than half the length of the CS-1e, the Sanken CS-M1 moisture-resistant ultracompact shotgun microphone is designed for capturing dialogue, foley, and sound effects in sterling sound quality while always staying out of the shot. Compared to the CS-1e, the CS-M1 is advantageous when used on close-range sources that don t produce extended bass frequencies.
For independent and major film, television, and location recording gigs where you need a space-saving mic that remains a featherweight on boompoles or short-lens cameras, the CS-M1 is ideal. It s short interference tube and consistent off-axis tone also make it well suited for indoor use.
The microphone exhibits a supercardioid polar pattern at low and midrange frequencies, and transitions to a lobar pattern at high frequencies, allowing it to attenuate the 90° off-axis points by about 10 dB from 250 Hz to 2 kHz and by over 14 dB at 4 kHz.
Resists Humidity and Temperature Changes
When working outdoors in humid environments, moisture and condensation can cause many mics to fail. The CS-M1 s rugged design and purpose-built components provide optimum resistance to humidity and hostile temperature changes, assuring dependable signal quality in a variety of environmental conditions.
Professional Sound Quality
The CS-M1 was built for use by independent videographers and demanding sound recordists alike. Its frequency response incorporates a rise in treble peaking at 9 kHz to increase intelligibility and a natural bass roll-off below 70 Hz to mitigate rumble. Its low self-noise of 16 dBA and ultrahigh sensitivity of -22 dB produce signal purity that s ready to be mixed.
Phantom Powered
Thanks to its 3-pin XLR output and compliance with 44 to 52 VDC phantom power, the CS-M1 is compatible with a variety of handheld audio recorders, field recorders, and mixer adapters as well as built-in preamps on many camcorders and cinema cameras.
Ideal for Mounting on a Boompole or Camera
Since the CS-M1 isn t bundled with a mic clip or shockmount, consider these separately available options to mount the CS-M1 and prevent the transfer of vibrations to the microphone. The Rycote INV-6 shockmount is perfect for mounting the CS-M1 on a boompole or traditional mic stand, and you can get a 3/8" -16 to shoe adapter to allow attachment to a camera s shoe. The CS-M1 s body features a matte black finish to prevent distracting visual reflections.
Windscreen Minimizes Wind Noise
The CS-M1 has a urethane windscreen to reduce unwanted wind noise from breezes, fans, heaters, and air conditioners. For maximum reduction of wind noise indoors and outside, consider the Rycote 7cm Classic-Softie furry windshield (available separately).
Rycote Standard Hole Classic Softie Wind-Screen (2.7" , 0.7 to 0.8" Diameter Hole, Gray)
Ideal for film, television, and broadcast production, the Rycote Standard Hole Classic Softie Wind-Screen is a compact, lightweight microphone windshield offering acoustically transparent reduction of wind noise while protecting your mic from dust and dirt. The slip-on fur windshield is designed for the Sanken CS-M1, and it is also compatible with microphone diameters from 0.7 to 0.8" including the Rode VideoMic NTG. The 2.7" Classic-Softie is handmade in the United Kingdom.
Thin-walled cavity design for acoustic transparency across the spectrum
Integral fur cover for enhanced wind-noise reduction
Rycote InVision INV-6 Microphone Suspension for Short/Small Condenser Mics (4.7" Long, 0.7 to 0.9" Diameter)
The Rycote INV-6 InVision Microphone Suspension addresses the demand for a professional Rycote-quality shockmount. Use in the studio, conference settings, and for speech capturing applications.
The entire mount is comprised of two InVision lyres with two clips that accommodate microphone bodies measuring 19 to 25mm in diameter. The lyres rest on a bar with a 3/8" threaded stand adapter at the base.
The stand adapter itself features an integrated cable clip for securing excess cable and minimizing noise. The unique Lyre suspension is engineered with Hytrel for a virtually indestructible design that maximizes shock and noise suppression.
The InVision suspension system is available in various clip sizes to accommodate different microphones. The versatile 19 to 25mm mounting clips included with this system are intended for mounting a wide variety of microphones (under 120mm long).
Large Lyre Suspension for Small Mics
The Rycote Lyre suspension webs measure 0.7 to 0.9" in diameter to accommodate small microphones. This is ideal for static stand mounting as well as boom placement.
0.7 to 0.9" Diameter Mounting Clips
The clips included with this system accommodate microphone diameters measuring between 0.7 to 0.9" in diameter (19 to 25mm). The clips mount a wide variety of microphones that measure under 4.7" long.
Hytrel Construction
The unique Lyre suspension is engineered with Hytrel for a virtually indestructible design that maximizes shock and noise suppression.
Integrated 3/8" Threaded Stand Adapter
A 3/8" threaded stand adapter is featured at the base for microphone stand mounting.
Sanken CS-M1 Moisture-Resistant Ultracompact Shotgun Microphone Specs
Microphone
Form Factor | Stand/Boom Mount |
Sound Field | Mono |
Operating Principle | Pressure Gradient |
Capsule | Electret Condenser |
Polar Pattern | Supercardioid |
Orientation | End Address |
Circuitry | Solid-State |
Pad | None |
High-Pass Filter | None |
Tone Adjustment | None |
Gain Adjustment | None |
Indicators | None |
On-Board Controls | None |
Windscreen | Foam (Included) |
Performance
Frequency Range | 70 Hz to 20 kHz |
Maximum SPL | 137 dB SPL (1% THD) |
Off-Axis Rejection | 4 dB at 60° 30 dB at 120° 12 dB at 180° |
Impedance | 140 Ohms at 1 kHz |
Sensitivity | -22 dBV/Pa at 1 kHz |
Equivalent Noise Level | 16 dB A-Weighted |
Connectivity
Analog Output | 1 x XLR 3-Pin |
Power
Operating Voltage | 48 V ± 4 V |
Operating Current Consumption | 4 mA |
Physical
Color | Black |
Mounting | Camera/Shoe-Mount, Shockmount (with Optional Hardware) |
Mounting Thread Size | No Mount Included |
Included Case | Soft Case |
Dimensions | : 0.75 x L: 4.06" / : 19 x L: 103 mm |
Weight | 1.94 oz / 55 g |
Packaging Info
Package Weight | 1.005 lb |
Box Dimensions (LxWxH) | 10.65 x 4.35 x 3.45" |
Rycote Standard Hole Classic Softie Wind-Screen (2.7", 0.7 to 0.8" Diameter Hole, Gray) Specs
Compatible Mic Diameter | 0.748 to 0.87" / 19 to 22 mm |
Inner Depth | 2.8" / 7 cm |
Material | Faux Fur |
Fur Length | 1" / 2.5 cm |
Outer Diameter | 4.7" / 12 cm |
Length | 3.9" / 10 cm |
Weight | 1.3 oz / 38 g |
Packaging Info
Package Weight | 0.385 lb |
Box Dimensions (LxWxH) | 10.6 x 4.2 x 3.2" |
Rycote InVision INV-6 Microphone Suspension for Short/Small Condenser Mics (4.7" Long, 0.7 to 0.9" Diameter) Specs
Compatible Microphone Diameter | 0.74 to 0.98" / 19 to 25 mm |
Max Microphone Length | 4.7" / 11.9 cm |
Mounting | 3/8"-16 |
Material of Construction | ABS Plastic, Rubber |
Packaging Info
Package Weight | 0.25 lb |
Box Dimensions (LxWxH) | 5.1 x 3.2 x 3.2" |
In the Box
- Windscreen
- Vinyl Case
- 2-Year Manufacturer Warranty
- Rycote Standard Hole Classic Softie Wind-Screen (2.7", 0.7 to 0.8" Diameter Hole, Gray)
- Rycote InVision INV-6 Microphone Suspension for Short/Small Condenser Mics (4.7" Long, 0.7 to 0.9" Diameter)
- Shoe Adapter
- Rycote Brush
- Rycote Sticker
Not in the Box
- Essential XLR Cables (Not Included)
No posts found