Behringer 150 RING MOD Overview
Build the synthesizer of your dreams with the Behringer 150 Ring-Mod / Noise / S& H / LFO, an authentic reproduction of the circuitry from the legendary Roland System 100M, allowing you to build your very own unique synthesizer that can fit in a standard Eurorack case for a very affordable price.
The 150 features a ring modulator which creates metallic and bell-like sounds that can be applied to any signal such as a sinewave or a signal from an LFO via the EXT SIG X/NOISE and EXT SIG Y/LFO jacks, and out of the RING MOD output. The LFO features 5 waveforms including sine, triangle, square, ramp, and sawtooth. Parameters can be further adjusted by the FREQ and DELAY sliders. The 150 includes a ribbon power cable and mounting screws.
Benefits
- Remarkable Ring Modulator / Noise Generator / S& H / LFO module from the '80s
- Authentic reproduction of original Roland System 100M circuitry
- Ring modulator for metallic and bell sounds
- 2 noise generators with simultaneous white and pink noise sources
- LFO features 5 waveforms: sine, triangle, square, ramp, and saw tooth, plus phase lock to keyboard
- 2 simultaneous LFOs with wide frequency range and delay controls, plus external CV input
- Sample and hold generator with clock-rate and lag-time controls, 3 way input selector for noise, LFO or external input
- 8 controls and switches give you real-time access to all important parameters
Sample and Hold
If you want to start layering your song on a droning note or maybe just create some ambience in your music, then you can connect any external signal source into the S& H circuit. A 3-way selector switch allows you to select which type of signal you are introducing into the SIG IN jack, whether its External Input, LFO, or Noise.
Eurorack Ready
Installing the 150 RING MOD / NOISE / S& H / LFO is designed to fit into a standard Eurorack case. Just connect the power cables to the power supply, and screw in the module using the included screws. This allows for the 150 to be mixed with other synth modules for a truly unique setup.
Behringer 150 RING MOD Specs
| Control | S&H Clock Rate: 1 x Slider, 2 to 25 Hz Lag Time: 1 x Slider, 0 to 8 Seconds Ext / LFO / Noise 3-Way: Sliding Switch LFO Freq Range: 3-Way Sliding Switch, (High/Mid/Low), Selectable Frequency: 1 x Slider, 0.03 to 30 Hz in 3 Ranges Delay 1 x Slider, 4 ms to 8 Seconds Waveform 5-Way Switch Sine / Triangle / Square / Sawtooth / Inverted Sawtooth, Selectable Output Level: 2-way Sliding Switch x1 / x10 or x1, Selectable |
| Signal Connectors | Ring Modulator Ext signal X / Y: 2 x 1/8" / 3.5 mm Jack X Impedance: 100 Kilohms Unbalanced Y impedance: 100 Kilohms Unbalanced Maximum Level: +20 dBu R.M Out: 1 x 1/8" / 3.5 mm Jack Impedance: 100 Ohms Unbalanced Maximum Level: +15 dBu Noise generator White 2 x 1/8" / 3.5 mm Jack Impedance 1 Kilohms Unbalanced Output Level 0 dBu Pink 2 x 1/8" / 3.5 mm Jack Impedance: 1 Kilohms Unbalanced Output Level: 0 dBu S&H Ext Signal: 1 x 1/8" / 3.5 mm Jack Impedance: 100 Kilohms Unbalanced Maximum Level: +17 dBu Ext Clock In: 1 x 1/8" / 3.5 mm Jack Impedance: 100 Kilohms Unbalanced Threshold: >1 V Clock Out: 1 x 1/8" / 3.5 mm Jack Impedance: 1 Kilohms Unbalanced S&H Out: 1 x 1/8" / 3.5 mm Jack Impedance: 1 Kilohms Unbalanced LFO Freq CV In: 1 x 1/8" / 3.5 mm jack Impedance: 100 Kilohms Unbalanced CV Input Range: 0 to +10 V LFO Out: 2 x 1/8" / 3.5 mm Jack Impedance: 1 Kilohms Unbalanced Output Level: 1 V p-p / 10 V p-p |
| Power | Power Supply: Eurorack Current Draw: 60 mA (+12 V), 50 mA (-12 V) |
| Rack Units | 16 HP |
| Dimensions | 1.7 x 3.2 x 5.1" / 4.4 x 8.1 x 12.9 cm |
| Weight | 0.35 lb / 0.16 kg |
In the Box
- Behringer 150 Ring-Mod / Noise / S&H / LFO Eurorack Module (16 HP)
- Eurorack Ribbon Power Cable
- Set of Mounting Screws
- 2-Year Manufacturer Warranty (Register within 90-Days for Extension)
Registration Extension: 2-Year
No posts found
