Behringer DI4000 Overview
The Behringer DI4000 V2 is an active direct injection (DI) box that packs four channels into a 1 RU rackspace. Equally suited for both studio use and live applications, this versatile DI-box provides impedance and signal matching for the direct connection of unbalanced line and instruments signals (from guitars, basses, keyboards, effect processors, and other line-level devices) to mixers and amplifiers. The unit operates on mains power.
On the back panel, each channel is equipped with two unbalanced inputs (XLR and 1/4" TS) and an unbalanced 1/4" TS link output (wired in parallel with the main output) to connect to your amp or monitor console. The channels also feature individual input attenuation switches to increase the operating range of the unit from the low-level signals of a high-impedance guitar to the hot speaker terminals of a PA amplifier.
On the front panel, each channel has its own balanced XLR output to connect individual signals to the main mixing board. Channels also feature an individual ground-lift switch, phase-reverse switch, high-cut filter switch, and +20 dB gain switch.
The The DI4000 V2 is equipped with illuminated switches that enable easy operation in dark environments. Accurate, 8-segment LED level meters let you see levels at a glance for each individual channel.
The unit uses Behringer OT-1 transformers to deliver an ultra-flat frequency response for pristine audio.
A Versatile Set of Tools for the Studio or Stage
- Switchable input attenuation allows input levels of up to +40 dB
- +20 dB gain switch for pre-amplification of low-level output signals
- Phase-reverse switch allows you to instantly correct phase problems
- Switchable high-cut filter (8 kHz) for guitar applications
- Ground-lift switch eliminates typical ground-loop problems
- Allows direct connection to speaker outputs with up to 3000W
- Accurate 8-segment LED level meter for optimum performance
- 1/4" TRS and gold-plated XLR connectors
- Illuminated switches enable operation in dark environments
- Internal switch-mode power supply (100-240 VAC) for noise-free audio and low power consumption
- Ultra-flat frequency response due to Behringer OT-1 transformers
EAN: 653341312839
Behringer DI4000 Specs
General
| Item Type | Rackmount DI |
| Number of Channels | 4-Channel |
| Active/Passive | Active |
| Circuitry | Solid-State |
| Pad | -20 / -20 dB |
| Ground Lift | Yes |
| Polarity Reverse | Yes |
| Gain/Trim Range | +20 dB |
| High-Cut/Low-Pass Filter | 8 kHz |
| Low-Cut/High-Pass Filter | No |
Connectivity
| Audio I/O | 4x XLR 3-Pin Unbalanced Input 4x 1/4" TS Unbalanced Input 4x 1/4" TS Unbalanced Thru 4x XLR 3-Pin Balanced Output |
Performance
| Frequency Response | 23 Hz to 60 kHz ±3 dB (100 Kilohms Load) 23 Hz to 40 kHz ±3 dB (600 Ohms Load) 23 Hz to 8 kHz (With High Cut) |
| Maximum Input Level | +60 dBu |
| Input Impedance | 220 Ohms (Pad Out) |
| Output Impedance | 600 Ohms |
| Total Harmonic Distortion/Noise | < 0.01% (at 1 kHz, +20 dBu) |
| Signal-to-Noise Ratio | -90 dBu (22 Hz to 22 kHz) |
Power
| Operating Voltage | AC Input |
| AC Input Power | 100 to 240 VAC, 50 / 60 Hz |
Physical
| Rackmount Size | 1 RU |
| Dimensions | 19 x 5.4 x 1.7" / 483 x 136 x 44 mm |
| Weight | 4.6 lb / 2.1 kg |
Packaging Info
| Package Weight | 5.5 lb |
| Box Dimensions (LxWxH) | 20.5 x 9.8 x 4.1" |
In the Box
- Behringer DI4000 V2 Rackmountable 4-Channel Active Direct Box
- IEC Power Cable
- 2-Years Manufacturer Warranty
No posts found
