Libec NX-300C Carbon Fiber Tripod System with NH30 Head, Ground Spreader, Long Plate & Case

Support your small camera rig weighing up to 22 lb and create smooth pan and tilt movements with this NX-300C Carbon Fiber Tripod System with NH30 Head, Ground Spreader, Long Plate & Case from Libec. The NX-300C system includes the NH30 dual 75mm bowl/flat base video head, the RT20C carbon fiber tripod, the SP-1B ground spreader, the Long Plate S balance plate, and an RC-20 carry case.

The base of the head fits the tripod s 75mm bowl, and it is also compatible with tripods with a flat mount. It features continuous pan/tilt drag and counterbalance, a snap-on/off quick release plate, an illuminated bubble level, and a pan bar. The Long Plate S is an extended camera plate to support larger, heavier rigs. The two-stage lightweight carbon fiber tripod weighs only 3.5 lb and can extend to a height of 60.6" . The ground spreader installs at the base of the tripod to add stability to the rig. The carry case stores and transports the entire system.

Libec NH30 75mm Ball/Flat Base Video Head with Pan Handle (22 lb Payload)

Designed to support small camera rigs weighing up to 22 lb, the NH30 75mm Ball/Flat Base Video Head with Pan Handle from Libec features a unified ball/flat mount design. The base of the tripod can fit either in a standard 75mm bowl or on a flat mount with a 3/8" -16 screw. Having both options available means you can transfer the head from a tripod with a bowl mount to a flat mount slider.

To achieve proper balance, the NH30 head includes a snap-on/off camera plate that can slide up to 1.2" of fore/aft adjustment, and it features 1/4" -20 and 3/8" -16 camera mounting screw options. The screw and locating pin are moveable to orient the plate on the camera to achieve the best possible balance. Once the camera is balanced, the continuous counterbalance and pan/tilt drag controls provide smooth movement. On the side, there are 1/4" -20 and 3/8" -16 threads to mount a variety of accessories such as a light, monitor, or extension arm.

Included with the NH30 is a pan handle that can be placed on the right or left side of the head by screwing it onto one of the mounts. The LED-illuminated bubble level helps to level the camera on uneven surfaces, even in low light.

Libec RT20C 2-Stage Lightweight Carbon Fiber Tripod with 75mm Bowl

Add a durable, lightweight tripod to your camera rig with this RT20C 2-Stage Lightweight Carbon Fiber Tripod with 75mm Bowl from Libec. The RT20C offers a 75mm bowl fitting for mounting a wide variety of fluid heads. The lightweight carbon fiber legs weigh only 3.5 lb. Secured by twist levers, the 2-stage legs have a height range of 14.6 to 60.6" . This tripod does not include rubber feet or a spreader, which can be purchased separately.

Libec RC-20 Carrying Case for NX-100C & NX-300C Tripods

The Libec RC-20 Carrying Case is designed to carry Libec NX-100C and NX-300C tripods systems. Made from a combination of materials that are resistant to water, wear, and tearing, the case has a soft non-padded lining that makes it easy to insert and remove your tripod without scratching its finish.

Construction

• Made of nylon, polyester, polypropene, polyethylene, acetal plastic & thermoplastic elastomer
• Combining multiple materials adds wear, water, and rip resistance
• Soft unpadded interior makes it easy to insert and remove tripod without marking or marring its finish
• Zipper closure

Pockets

• Large main compartment holds a NX-100C or NX-300C tripod system
• Zippered exterior slip pocket
• Open exterior slip pocket

Carrying options

• Soft connecting carry handles
• Carry handles are located off-center for proper load balance with the tripod system inside
• Attached, adjustable shoulder strap
• Weighs just over a pound empty

Libec Long Sliding Plate S for TH-X, TH-Z, NH10 & NH30 Heads

This Long Sliding Plate S from Libec helps to properly balance a heavier camera or camera rig with a longer lens on select tripod heads. This 9.4" long plate is constructed from an aluminum alloy and offers a 3.7" sliding range. It is compatible with Libec TH-X, TH-Z, NH10, and NH30 heads, as well as select Manfrotto and Sachtler heads.

Sliding Plate

Measures 9.4" long with a sliding range of 3.7"

Compatibility

• Libec TH-X, TH-Z, NH10, and NH30 heads
• Select Manfrotto and Sachtler heads

Aluminum Alloy

Durable aluminum alloy construction