Miller CiNX 3 Fluid Head with ENG Carbon Fiber 2-Stage Heavy-Duty Tripod Kit

Miller CiNX 3 Fluid Head

The Miller CiNX 3 Fluid Head is designed with a strength-to-size ratio that provides an optimal solution for the supported load capacity of 2.2 to 41.8 lb. The CiNX 3 features a 3/8 -16 threaded flat base and includes a 100mm bowl claw adapter optional 150mm bowl or Mitchell base adapters from Miller are also supported.

The CiNX 3 head features 16 steps of counterbalance and 6 steps of pan and tilt fluid drag. The drag and counterbalance systems offer progressive and equal increments of drag and torque to ensure ultra-soft starts and stops and balanced diagonal transitions. The pan/tilt controls and a bubble level are all illuminated at the press of an illumination button. The CiNX 3 comes with a GP23A type battery already installed for illumination but supports multiple other types as you will find in the user manual.

For ultimate efficiency with heavy cameras, the CiNX 3 has a sideload camera plate platform with a safety lock, and it comes with an ARRI-type camera plate that can be adjusted approximately 6 . It also includes a rosette-mount telescopic pan handle while supporting two in total for dual-handed operation. On the sides, it provides four anti-twist ARRI accessory mounts. The head is made of lightweight yet high-strength die-cast aluminum and rigid composite polymers. It s finished with a durable black ripple and anti-corrosive pretreatment. It also has water- and dust-resistant sealing.

The head also has a very wide operating temperature range of -40 to 149° F.

Key Features

• Fluid drag system with smooth start and soft stop technology and balanced diagonal transitions
• 3/8 -16 threaded flat base
• Includes a 100mm bowl claw adapter (optional 150mm bowl or Mitchell base adapters supported)
• 16 steps counterbalance
• Payload range of 2.2 to 41.8 lb
• 6 steps of pan and tilt drag illuminated controls
• Sideload platform with safety lock
• 5.9 camera plate sliding range
• Four anti-twist ARRI accessory mounts
• Illuminated bubble level
• Pan handle included optional second one supported
• Wide operating temperature range of -40 to 149° F

Miller ENG Carbon Fiber 2-Stage Heavy-Duty Tripod Legs (100mm Bowl) - Supports 200 lbs

HD Series tripods are designed with single or two-stage legs, and made of aluminum alloy or carbon fiber material. Offers a 100 or 150mm bowl fixing, attached to a ball-leveling mount that ensures bowl-to-leg fastening, resists loosening and eliminates joint instability. Innovated Quik-Lok locking mechanism, lets you set up the tripod within seconds. These heavy-duty tripods offer utmost strength and tortional rigidity to take the full ENG/EFP workload providing optimum security when supporting studio camera configurations.

Heavy-duty carbon fiber construction

100mm / 4 bowl base

Double extension design

Quik-Lok rapid, non slip clamping system, with self-adjusting brake mechanism for smooth, positive clamp action

Maximum height of 63.0-inch

Supports up to 200 lb

Split carry handle, splits apart for set up and combines for balanced, safe carriage when the tripod is collapsed

Miller 993 Mid-Level Spreader

The Miller 993 Mid-Level Spreader is a mid-level spreader for Sprinter, Arrow 25/40, and HD tripod systems. This device offers variable adjustment in minimum and maximum height settings, plus a latch and swivel design.

Miller 475 Rubber Feet Pads for Select Tripods (Set of 3)

The 475 Tripod Feet from Miller are a set of three rubber snap-on feet designed to be used in any situation where the integrated dual spiked feet are not optimal. They are ideal for use on both slippery and glossy floors. These rubber feet are compatible with all tripods with a 993 mid level spreader.