Miller CiNX 7 & HDC MB 1-Stage Aluminum Tripod System with Mitchell Base Adapter & Mid-Spreader

Miller CiNX 7 Fluid Head

Miller s CiNX 7 Fluid Head features a payload of 13.2-55 lb, 16 steps of counterbalance, and 7 + 0 steps of pan and tilt drag. It s designed with a strength-to-size ratio that provides an optimal solution for the supported load capacity. The drag and counterbalance systems offer progressive and equal increments of drag and torque to ensure ultra-soft starts and stops and balanced diagonal transitions. The CiNX 7 provides a smooth and effective workflow for heavy camera setups.

The CiNX 7 features a 3/8 -16 threaded flat base and includes a 100mm bowl claw adapter. Additionally, optional 150mm bowl or Mitchell base adapters from Miller are also supported.

The pan/tilt controls and a bubble level are all illuminated at the press of an illumination button. The CiNX 7 comes with a GP23A type battery already installed for illumination but supports multiple other types as you will find in the user manual.

For ultimate efficiency with heavy cameras, the CiNX 7 has a sideload camera plate platform with a safety lock, and it comes with an ARRI-type camera plate that can be adjusted approximately 6 . It also includes a rosette-mount telescopic pan handle while supporting two in total for dual-handed operation. On the sides, it provides four anti-twist ARRI accessory mounts. The head is made of lightweight yet high-strength die-cast aluminum and rigid composite polymers. It s finished with a durable black ripple and anti-corrosive pretreatment. It also has water- and dust-resistant sealing.

The head also has a very wide operating temperature range of -40 to 149° F.

Key Features

• Fluid drag system with smooth start and soft stop technology and balanced diagonal transitions
• 3/8 -16 threaded flat base
• Includes a 100mm bowl claw adapter (optional 150mm bowl or Mitchell base adapters supported)
• 16 steps counterbalance
• Payload range of 13.2 to 55 lb
• 8 steps of pan and tilt drag illuminated controls
• Sideload platform with safety lock
• 5.9 camera plate sliding range
• Four anti-twist ARRI accessory mounts
• Illuminated bubble level
• Pan handle included optional second one supported
• Wide operating temperature range of -40 to 149° F

Miller HDC MB Mitchell Base 1-Stage Aluminum Tripod

The Miller HDC MB Mitchell Base 1-Stage Aluminum Tripod is designed for users who require high levels of stability and low torsional distortion, even at maximum drag. It features a Mitchell Base and supports up to 210 lb loads. It has heavy-duty 24mm alloy tubing and quick-action rotary screw type leg locks, which allow for maximum lock off performance without need for maintenance. This heavy-duty tripod is optimized for use with the Miller 993 mid-level spreader.

Miller Mitchell Base Adapter for Skyline 70 Fluid Head

The Miller Mitchell Base Adapter allows the Skyline 70 Fluid Head to be connected with a Mitchell base and can be used with heavy-duty Mitchell tripods.

Miller 993 Mid-Level Spreader

The Miller 993 Mid-Level Spreader is a mid-level spreader for Sprinter, Arrow 25/40, and HD tripod systems. This device offers variable adjustment in minimum and maximum height settings, plus a latch and swivel design.

Miller 478 Rubber Feet Pads for Select Tripods (Set of 3)

The 478 Tripod Feet from Miller are a set of three rubber snap-on feet designed to be used in any situation where the integrated dual spiked feet are not optimal. They are ideal for use on both slippery and glossy floors. These rubber feet are compatible with the HD MB 1-stage tripod (alloy).

Miller Long Smart Tripod Case with Wheels for 1 Stage HD Systems (Black)

Store, transport, and protect a select Miller system tripod with the black Miller Long Smart Tripod Case with Wheels for 1 Stage HD Systems. The case features a latch closure, inner padding, a neoprene O-ring, an automatic air pressure valve, and an IP67 watertight rating. For strength and durability, the case is constructed from special polymers and aluminum. Carry the case with the top and center handles or roll with the built-in wheels.

Watertight (IP67), resistant to dust, moisture, acids and sand.

Ergonomic handle made of PP SEBS material with steel pins to provide a strength and ergonomics.

Automatic valve which automatically adjusts the air pressure inside.

Internal O-ring made of neoprene PA66 makes the suitcase totally waterproof.

Materials: made of a patented material given by a special compound based on polypropylene TTX01, glass fiber and rubber.

The case opens along the long side and uses 4 latches and can be locked (not included) if required.