Audioengine HD3 Bluetooth Speaker System with DS1 Desktop Stands Kit (Walnut, Pair)

The HD3 Bluetooth Speaker System with DS1 Desktop Stands Kit includes a pair of walnut grain Audioengine HD3 wireless Bluetooth speakers and a pair of DS1 desktop stands. The stands are made from a noise-dampening silicone rubber and position each speaker at an upward-facing 15° angle. Whether you re streaming music to your HD3 speakers via your phone or tablet, or playing a component through its RCA or 3.5mm inputs, the DS1 stands can better optimize your audio experience.

Audioengine HD3 Bluetooth Speaker System (Walnut, Pair)

Enjoy your audio from nearly any source with this pair of walnut Audioengine HD3 Bluetooth Speaker System. They feature Bluetooth with aptX HD for wireless connectivity, stereo RCA and 1/8" inputs for traditional wired devices, and a micro-USB input for a dedicated input from your computer. The HD3 has a 2-way design with two built-in, 15W per channel amplifiers. Each speaker sports a 2.75" Kevlar woofer and a 0.75" silk dome tweeter.

No Missed Connections

Connect to the HD3 any way you like: wirelessly or wired, digital or analog. Stream your music library, TIDAL, Spotify, Pandora, YouTube, etc. to the HD3 from just about anywhere in your house (within 100 ) without dropouts. Wireless setup is designed for simplicity and only takes about a minute. And if you re using the HD3 on your desktop, connect it with a USB cable. The USB input bypasses your computer s built-in headphone jack for an enhanced listening experience. If you re not keen on USB or wireless, you can still use any stereo RCA or 1/8" audio cable to connect.

Expandability

The HD3 is expandable, so if you want deeper bass, just connect your subwoofer.

Plug In Your Headphones

The HD3 includes a dedicated headphone output on the front panel, so you can listen without waking the neighbors. Its headphone amplifier is designed to deliver quality sound that drives even the most demanding headphones.

Retro-Forward Design

The HD3 features aluminum trim accents and detachable magnetic grilles designed to blend with any d cor.

Built-In Amplifiers

Built-in power amplifiers save space and eliminate the need to connect the HD3 to a stereo receiver or external power amp. Simply plug the left speaker into a power outlet and connect the included speaker wire from the left to the right speaker. All internal components of the HD3 are designed and tuned together for a more uniform sound than traditional separate speakers and amplifier.

Integrated Design

The speaker cabinets, drivers, bass port designs, amplifiers, and passive crossovers are all tuned together specifically for the HD3. This is designed to provide for a more efficient system that requires less power than passive speakers and a separate integrated amplifier or similar A/V components.

Built-In B1 and D1

Features from the Audioengine B1 aptX HD Bluetooth receiver and D1 24-bit DAC are combined in the HD3 to help make it a complete digital audio system.

Bluetooth and aptX HD

The HD3 is designed to easily connect to any of your devices that have Bluetooth, but for enhanced sound quality, use a device that supports Bluetooth aptX HD. For Apple devices that don t have aptX HD, such as the iPad or iPhone, Apple generally uses the AAC codec. It sounds good as well, and you ll get the extra benefit of the upsampling 24-bit DAC.

Extended Wireless Range

Through signal management circuitry and antenna tuning, the HD3 offers a solution that has up to three times the range of standard Bluetooth for multi-room use with no degradation in audio quality.

24-Bit DAC

The HD3 Bluetooth receiver and USB input both utilize the PCM 5102 DAC, which is designed for low-noise and high-fidelity. The PCM 5102 is used as an upsampling DAC and will pad all bit depths to 24-bit, achieving a higher signal-to-noise ratio and lower noise floor. Due to the high signal-to-noise specs of the PCM 5102, the fact that digital signal is upsampled to 24-bits “ as well as the added benefit of onboard triple-redundancy power source conversion and filtering “ the HD3 Bluetooth implementation presents low noise and low distortion characteristics with a noticeable improvement over other Bluetooth devices.

HD3 Headphone Amplifier

The HD3 contains a headphone amplifier based on the OPA2134 low-noise opamp. This amp is designed to provide low-impedance, high-fidelity audio and a 2V output, which can drive a wide range of headphones.

Amplifier Design

The amplifiers in the HD3 are located in the left speaker and are a class A/B analog monoblock design. This is a more traditional speaker/amplifier configuration, which is designed to provide quality audio and greater flexibility. All circuit boards for the power and preamp sections are vertically mounted for enhanced mechanical shock protection.

Driver Designs

The HD3 uses ferrofluid-cooled silk dome tweeters with neodymium magnets. Silk tweeters are fashioned to hold up well under high power, and the edge-driven design gives a smooth response. The woofers are Kevlar-woven glass-aramid composite with rubber surrounds. Kevlar is designed for strength, so the woofer can retain its shape when being driven at high levels.

Magnetic Shielding

The speaker drivers in the HD3s are directly magnetically shielded.

Additional Features

• RCA and 1/8" audion inputs for easy connection to various audio sources, including a turntable or TV
• USB input for computer connection with up-sampling 24-bit DAC
• 0.75" thick MDF cabinets with wood veneer

EAN: 852225007032

Audioengine DS1 Desktop Stand for Small Speakers

The DS1 Desktop Stand from Audioengine is a simple solution for desktop speakers. The DS1 speaker wedge is a great way to get your Audioengine A2+, HD3, or other small speakers up off your desk and at an angle right where you need them.

Acoustic dampening isolation stands

Fits most desktop speakers

15° angle

EAN: 819955200010